XCSOURCE 3pcs MCP2515 CAN Bus Module TJA1050 Receiver SPI for Arduino 51 MCU ARM Controller Development Board TE534

#ad
XCSOURCE TE534 #ad - Except the power indicator Dimension: 4. 4cm x 2. 8cm screw hole center spacing: 23mm x 38mm working temperature: -40¡ãc ~ 85¡ãC Package Includes: 3 x MCP2515 CAN Bus Module TJA1050 Receiver Supports can v2. 0b specification, the communication speed 1Mb/s. 0 to 8-byte data field. With standard frame, expand the frame and remote frame.

With impedance matching, ensures the drive capacity, long-distance data transmission against signal radiation. Working current: 5mA 1 microamp standby current. 0 to 8-byte data field. With impedance matching, ensures the drive capacity, long-distance data transmission against signal radiation. 120 ohm termination resistors.

XCSOURCE 3pcs MCP2515 CAN Bus Module TJA1050 Receiver SPI for Arduino 51 MCU ARM Controller Development Board TE534 #ad - Features: supports CAN V2. 0b specification, the communication speed 1Mb/s. Except the power indicator. With standard frame, expand the frame and remote frame. 5v dc power supply module, SPI interface protocol control. 120 ohm termination resistors. Specifications: working voltage: DC 5V Working current: 5mA 1 microamp standby current.

#ad



Waveshare SN65HVD230 CAN Board Connecting MCUs to CAN Network Features ESD Protection Communication Evaluation Development Board 3.3V

#ad
Waveshare SN65HVD230 CAN Board #ad - Compatible with PCA82C250 Powered from 3. 3v. Connecting mCUs to the CAN network. Features sn65hvd230 onboard can transceiver SN65HVD230 Features ESD protection. The sn65hvd230 can board is ideal for connecting microcontrollers to the CAN network. Overview the sn65hvd230 can board is an accessory board features an onboard CAN transceiver SN65HVD230, which is pinout compatible with PCA82C250

It is powered from 3. 3v and features ESD protection.

#ad



seeed studio CAN-Bus Shield V2 Compatible with Arduino

#ad
Seeedstudio . #ad - Changeable chip select pin changeable cs pin for tf card slot changeable int pin screw terminal that easily to connect CAN_H and CAN_L Arduino Uno pin headers 2 Grove connectors I2C and UART SPI Interface up to 10 MHz Standard 11 bit and extended 29 bit data and remote frames Two receive buffers with prioritized message storage Technical details Dimensions:74.

8mm x53. 4mm x27. 1mm weight:G. W 48g battery:exclude part list can-bus shield V2*1 Onboard can transceiver SN65HVD230 Compatible with PCA82C250 They are all awesome shields that widely liked by our users. Previously we have made two versions of CAN-BUS Shield, the V1. 0 and V1. 2. Powered from 3. 3v. It is commonly found on modern machine tools and as an automotive diagnostic bus.

seeed studio CAN-Bus Shield V2 Compatible with Arduino #ad - Can-bus is a common industrial bus because of its long travel distance, medium communication speed and high reliability. In order to make it better, several months ago we conducted a survey about CAN-BUS Shield V1. 2 and received many valuable advices thanks to all the users who replied to us, so we decided to make an update and here it is - CAN-BUS Shield V2.

#ad



ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 Nano x 3 Without Cable

#ad
ELEGOO EL-CB-005 #ad - It lacks only a dc power jack, and works with a Mini-B USB cable instead of a standard one. The nano is using the chips atmega328p and cH340, not FT232 as official Arduino, so pls. First and most importantly, obd-ii or can standard pinout can be selected by switching jumpers on DB9 interface, the default pinout is OBD-II.

Secondly we add a tf card slot for data storage and the cs pin can be either set to D4 or D5. The int pin can also be set to D2 or D3 by switching jumpers on the back of the shield. Can bus shield work well with arduino uno atmega328, arduino mega ATmega1280/2560 as well as Arduino Leonardo ATmega32U4 and LinkIt One.

ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 Nano x 3 Without Cable #ad - You could download the driver of Elegoo Nano V3. 0 at: http://bit. Ly/2jklJMO. It is commonly found on modern machine tools and as an automotive diagnostic bus. Thanks for can-bus, makers are able to hack their cars more conveniently. The can-bus shield v2 still uses mcp2515 as can-buS controller and MCP2551 as CAN transceiver.

Despite of that, there are really many updates. The power source is automatically selected to the highest voltage source. Use the driver from above link.

#ad



MakerFocus CAN-Bus Shield V1.2

#ad
Makerfocus 8541549126 #ad - Two receive buffers with prioritized message storage; Operating voltage: DC5-12V. This can-bus shield adopts mcp2515 can bus controller with spi interface and MCP2551 CAN transceiver to give your Arduino/Seeeduino CAN-BUS capability. We have a strong after-sales service team: as long as you have any questions about the product, we will resolve your issue immediately if received your email, your satisfactory purchase experience is our greatest hope! How to email us? Plz click "MakerFocus" and click "Ask a question" to email us! Looking forward to your consultation!

Connecting mCUs to the CAN network. Features ESD protection. Compatible with PCA82C250 The nano is using the chips atmega328p and cH340, not FT232 as official Arduino, so pls. It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper. Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, GND on one top, ATN, so users have more breadboard space.

MakerFocus CAN-Bus Shield V1.2 #ad - The int pin can also be set to D2 or D3 by switching jumpers on the back of the shield. Can bus shield work well with arduino uno atmega328, arduino mega ATmega1280/2560 as well as Arduino Leonardo ATmega32U4 and LinkIt One. You could download the driver of Elegoo Nano V3. 0 at: http://bit.

#ad



uxcell 10 Pcs HC-49S DIP Quartz Crystal Oscillator 16MHz 16.000M Hz 16.000MHz

#ad
uxcell a14050500ux0216 #ad - Standard 11 bit and extended 29 bit data and remote frames; Industrial standard 9 pin sub-D connector; Size: 78mmx53. 5m. Weight : 6g;package Content : 10 x Crystal Oscillator. Of pins : 2;effective series resistance : 30 ohm;sizeEach One : 11. 5 x 4. 5 mm/ 045" x 018"l*w. No. It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper.

Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, GND on one top, ATN, so users have more breadboard space. Compatible with PCA82C250 Mount height : 4mm / 016";material : Metal & Electronic Parts. Quartz crystal enclosed in an hermetically sealed hc-49/us package.

uxcell 10 Pcs HC-49S DIP Quartz Crystal Oscillator 16MHz 16.000M Hz 16.000MHz #ad - . Thanks for can-bus, makers are able to hack their cars more conveniently. The can-bus shield v2 still uses mcp2515 as can-buS controller and MCP2551 as CAN transceiver. Despite of that, there are really many updates. Widely used in tv, pc cards, electronic meter, MP3, DVD, automobile electronics, etc.

#ad



Fotag OBD2 16 pin to DB9 RS232 Serial Port Adapter Cable Diagnostic Extension Cable with Power Switch to Avoid Battery Drain 1.5M 5ft

#ad
Guangzhou Fotag commerce co., LTD #ad - Weight : 6g;package Content : 10 x Crystal Oscillator. Features ESD protection. The nano is using the chips atmega328p and cH340, not FT232 as official Arduino, so pls. Can-bus is a common industrial bus because of its long travel distance, medium communication speed and high reliability. Please be mention clear, 7:4, 5:1, be sure and understand your application before selecting this cable the pin-out is : OBD II : DB 9 = 4, 4, 15:8, 14:5, 10:6, 6:3, 2:7, 5:2, 16:9 ; The on/off switch controls 16:9 connection.

It's got a pin layout that works well with the Mini or the Basic Stamp TX, RX, power and ground on the other. The nano can be powered via the mini-b usb connection, 7-12V unregulated external power supply pin 30, or 5V regulated external power supply pin 27. Two receive buffers with prioritized message storage; Operating voltage: DC5-12V.

Fotag OBD2 16 pin to DB9 RS232 Serial Port Adapter Cable Diagnostic Extension Cable with Power Switch to Avoid Battery Drain 1.5M 5ft #ad - The int pin can also be set to D2 or D3 by switching jumpers on the back of the shield. Can bus shield work well with arduino uno atmega328, arduino mega ATmega1280/2560 as well as Arduino Leonardo ATmega32U4 and LinkIt One. You could download the driver of Elegoo Nano V3. 0 at: http://bit. Ly/2jklJMO. It's just a cable with two different types of connectors on each end.

#ad



LAFVIN Nano V3.0, Nano Board ATmega328P 5V 16M Micro-Controller Board Compatible with Arduino IDE Nano x 3 with USB Cable

#ad
LAFVIN 8541582500 #ad - Mount height : 4mm / 016";material : Metal & Electronic Parts. Two receive buffers with prioritized message storage; Operating voltage: DC5-12V. Standard 11 bit and extended 29 bit data and remote frames; Industrial standard 9 pin sub-D connector; Size: 78mmx53. 5m. Compatible with PCA82C250 Features ESD protection.

Ultra slim】the obd2 16 pin to db9 rs232 female port Cable is ultra slim and flat for superior flexibility and durability. Power switch】 with power switch, we designed the useful power switch of this OBD cable to prevent battery damage. 8 pins out】the pin-out is : obd ii : db 9 = 4, it is 8 pin out, 4, 2:7, 10:6, 16:9 ; the on/off switch controls 16:9 connection.

LAFVIN Nano V3.0, Nano Board ATmega328P 5V 16M Micro-Controller Board Compatible with Arduino IDE Nano x 3 with USB Cable #ad - The power source is automatically selected to the highest voltage source. Note: can bus shield comes unassembled, soldering is required. More detail pls refer to: https://www. Youtube. Com/watch?v=ol9co9yagYE; Resources: https://drive. Google. Com/drive/folders/1cztz4is2b1mfpr4O69H2fo2UPJBmgpnw?usp=sharing; https://drive.

#ad



HiLetgo USB Logic Analyzer Device With EMI Ferrite Ring USB Cable 24MHz 8CH 24MHz 8 Channel UART IIC SPI Debug for Arduino ARM FPGA M100 SCM

#ad
HiLetgo #ad - Sampling rate up to: 24 mhz, can be 24mhz. Powered from 3. 3v. We have a strong after-sales service team: as long as you have any questions about the product, we will resolve your issue immediately if received your email, your satisfactory purchase experience is our greatest hope! How to email us? Plz click "MakerFocus" and click "Ask a question" to email us! Looking forward to your consultation!

It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper. Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, ATN, GND on one top, so users have more breadboard space. General applications around 10M, enough to cope with a variety ofoccasions;.

HiLetgo USB Logic Analyzer Device With EMI Ferrite Ring USB Cable 24MHz 8CH 24MHz 8 Channel UART IIC SPI Debug for Arduino ARM FPGA M100 SCM #ad - . Mount height : 4mm / 016";material : Metal & Electronic Parts. It is commonly found on modern machine tools and as an automotive diagnostic bus. 16mhz, 200khz, 2mhz, 12mhz, 100khz, 50khz, 4mhz, 250khz, 1mhz, 8mhz, 500khz, 25khz; the logic for each channel sampling rate of 24M/s. The power source is automatically selected to the highest voltage source.

Note: can bus shield comes unassembled, soldering is required. More detail pls refer to: https://www.

#ad



PJRC Teensy 4.0 Without pins

#ad
PJRC #ad - General applications around 10M, enough to cope with a variety ofoccasions;. Improved new version CH340G Replace FT232RL. Lafvin nano v3. 0 card is 100% compatible with the Nano card, and fully compatible with Windows, Mac and Linux operating system. Works the same as original Nano, runs perfectly on programming software.

Using atmel atmega328p-au mcu, support ISP download; Support USB download and Power. Lafvin nano ch340 controller is a compact board similar to the R3 board, smaller and breadboard-friendly than Diecimila. The logic for each channel sampling rate of 24M/s. No. 2 i2s digital Audio. General applications around 10M, enough to cope with a variety ofoccasions; 8-channel.

PJRC Teensy 4.0 Without pins #ad - Product name : crystal oscillator;Output Frequency : 16MHz;Frequency Tolerance : ±20ppm. It's just a cable with two different types of connectors on each end. This is not a signal convert level adapter. Original atmega328p ch340 chip is used. Input voltage range: -05v to 5.

#ad



ELEGOO MEGA 2560 R3 Board ATmega2560 ATMEGA16U2 + USB Cable Compatible with Arduino IDE, RoHS Compliant

#ad
ELEGOO EL-CB-003 #ad - Product name : crystal oscillator;Output Frequency : 16MHz;Frequency Tolerance : ±20ppm. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started. It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper.

Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, ATN, GND on one top, so users have more breadboard space. The mega is 100% compatible with arduino IDE and most shields designed for the Arduino mega2560 r3,RoHS Compliant. The second one is a not connected pin, the IOREF that allow the shields to adapt to the voltage provided from the board.

ELEGOO MEGA 2560 R3 Board ATmega2560 ATMEGA16U2 + USB Cable Compatible with Arduino IDE, RoHS Compliant #ad - Input impedance: 1mohm || 10pf typical, approximate; Crystal: +/-20ppm, 24MHz. Sampling rate up to: 24 mhz, can be 24mhz. 5 * 2. Features ESD protection. 1mm dc barrel jack compatible with 5. Can-bus is a common industrial bus because of its long travel distance, medium communication speed and high reliability.

2048k flash 64k reserved for recovery & EEPROM emulation. This version is optimized in the original version, mainly for customers under the functional requirements for product quality and high case designed both to ensure consistent and compatible with the original, but also easy to use.

#ad